minimum thickness

英 [ˈmɪnɪməm ˈθɪknəs] 美 [ˈmɪnɪməm ˈθɪknəs]

网络  最小厚度

化学



双语例句

  1. The axial frictional pulling force and the minimum thickness of mucus film were analyzed and calculated in detail when rectangular or trapezoidal cylindrical screw was being adopted in microcomputer.
    详细分析计算了微型机器人在采用矩形和梯形圆柱螺旋时的轴向摩擦牵引力和最小粘液膜厚度。
  2. A formula to calculate the minimum thickness of cushion under rigid structural layer is derived by mechanics analysis on the fill column above the deep mixing pile.
    根据褥垫层的受力机理,导出计算刚性结构层下褥垫层最小厚度的理论公式。
  3. The anode profile of the nozzle is optimized by the proposed method, and the nickel deposit is obtained, which is1.26 of the ratio of maximum thickness to minimum thickness.
    对某型喷管外壁进行阳极轮廓优化设计后,制得了厚度最大处与最小处比值为1.26的电铸镍层。
  4. The new conveyor system composed by rolls and flat belts makes this unit particularly suitable for the management of flexible or of minimum thickness panels.
    改良的转向器系统由滚轮和传送带构成,使得该机器特别适合软板和薄板操作。
  5. Research on Methods for Testing Minimum Thickness of Cement Soil Cut-off Wall Body
    水泥土截渗墙墙体最小厚度测试方法研究
  6. The function's proceeding every kind of degree of hardness parameter converts automatically mutually, discriminating to try an environment for the minimum thickness experiments with the measurement temperature.
    该机能进行各种硬度参数相互自动换算,鉴别试件最小厚度和测定试验的环境温度。
  7. Mini Scan This is a minimum thickness scan and allows the user to run the probe over the wall surface.
    迷你扫描这是一个最小厚度扫描并允许用户运行探针的墙面。
  8. The minimum thickness was mainly determined by the maximal internal pressure.
    影响最小厚度的主要因素是最大内部压力。
  9. Some Suggestions on Acceptance Standards of Minimum Thickness of Convex Head
    对凸形封头最小厚度验收标准的看法和建议
  10. A calculation is made in this paper for the minimum thickness limit of the Zhaozhou Arch Bridge and its safety factors under a concentrated live load of98.1KN.
    本文计算了一个集中活荷载(98.1kN)通过赵州桥时拱圈最小厚度和拱厚安全度的变化。
  11. Integrating with stress analysis 、 structural computation and drainage analysis, minimum thickness value of porous concrete base is calculated;
    综合应力分析、结构计算和路面排水分析两方面要求,得出多孔混凝土基层所需的最小厚度;
  12. In numerical simulation minimum thickness was taken as forming limit criterion. The research on the relation between minimum thickness and strain paths was carried out.
    在数值模拟中应用最小厚度作为成形极限判据,研究最小厚度值与应变路径的关系。
  13. The paper analyses the minimum thickness of shaped shell and deduces its formula.
    对成形壳体的最小壁厚的控制位进行了分析并给出了相应的计算式。
  14. Results of experiment show that the minimum thickness of cut is in proportion to the cutting edge radius.
    实验结果表明,最小磨削厚度是与磨削刃半径成比例的。
  15. The direct influence on minimum thickness of oil film from lube oil viscosity and main bearing gap has been proved.
    而理论计算证明,润滑油粘度和主轴承间隙对最小油膜厚度有着直接的影响。
  16. Sheet Metal Forming Limit Prediction with Minimum Thickness Criterion in Numerical Simulation
    数值模拟中应用最小厚度准则预测板料成形极限
  17. As an important piece of work in hydraulic engineering, it is the key to determine the minimum thickness of overlying rock formation of the tunnel under pressure.
    水工建筑中,据岩体的强度特性和内水压力的大小,精确确定有压隧硐上覆岩层最小厚度是非常重要的。
  18. Based on different fit clearance of journal sliding bearing, the constituent changing mechanism of blood lubricant film and its influence on blood lubrication stability were analyzed, the minimum thickness of film for stable lubricant of blood was brought forward.
    结合径向滑动轴承不同配合间隙,分析了血液润滑膜组分变化机制及组分变化对血液润滑稳定性的影响规律,提出了保证血液稳定润滑的最小膜厚。
  19. Direct Calculation of the Minimum Thickness of Cushion with Filling Replacement
    换填法垫层最小厚度的直接计算法
  20. Combining with actual example, for shaped head, the minimum thickness is reasonable to be scaled in diagram.
    通过分析讨论并结合实际,指出成形封头应在图面上以最小厚度标出最为合理。
  21. By analysing those photographs, it was found that increasing the drawing speed, reducing the ratio of maximum thickness of liquid meniscus to its minimum thickness, and eliminating the electromagnetic stir all reduced the oxidation and formation of oxide fold, and therefore a good surface quality.
    发现增大抽拉速度,减小液柱头最大厚度与最小厚度的比值,以及抑止电磁搅拌都能减小氧化和氧化皱褶的形成,最终改善表面质量。
  22. For working out the thickness of the shoe more accurate, the edge is converted to the curve through curve fitting. By comparing the two curves, the paper get the minimum thickness of the shoes and analyses the error.
    对闸瓦边缘进行曲线拟合,比较判断出最小厚度值,对产生的误差进行分析。
  23. Through the calculation of the minimum thickness of cutting, the influence of micro-milling arose from the cutting edges obtuse radius and minimum cutting thickness in scale effect is analysed.
    通过对最小切削厚度的计算,分析了尺度效应中的切削刃钝圆半径、最小切削厚度对微细铣削加工的影响。
  24. In the process of micro-machining, the new theoretical and technological problems were put forward because of the size effect and the minimum thickness of cutting.
    在微细切削加工过程中,由于尺度效应和最小切削厚度的原因,使得新的理论与工艺问题凸现出来。
  25. Lightweight aggregate concrete steel fibers in the indoor humidity in the environment minimum thickness values can be protected in accordance with the ordinary concrete to determine.
    钢纤维轻骨料混凝土在室内潮湿环境中的最小保护层厚度取值可以按照普通混凝土的来确定。